A A Literature-Grounded Framework for Thermomechanical Modelling of Orthogonal Cutting in Long SiC-Fibre-Reinforced Ti-6Al-4V Composites
DOI:
https://doi.org/10.55927/eajmr.v5i11.26Keywords:
SiC-fibre-reinforced Ti-6Al-4V, Orthogonal Cutting, Finite-Element Modelling, Thermomechanical Coupling, Interfacial DamageAbstract
This study presents a literature-grounded thermomechanical finite-element framework for investigating orthogonal cutting of long SiC-fibre-reinforced Ti-6Al-4V composites under cryogenic (−180 °C), ambient (24 °C), and elevated-temperature (400 °C) conditions. The framework integrates titanium-matrix plasticity, brittle SiC-fibre fracture, fibre–matrix interfacial damage, tool–workpiece contact, and thermal effects. Particular attention is given to the transferability of Johnson–Cook parameters, constitutive-model limitations at cryogenic temperatures, and cohesive-zone calibration. Numerical verification, experimental validation, mesh sensitivity, and parameter uncertainty are incorporated into the proposed workflow. As solver outputs and new experimental measurements are not yet available, quantitative predictions are not claimed. The framework establishes a reproducible basis for future simulation and validated assessment of cutting forces, fracture, and subsurface damage.
References
S. Zan, Z. Liao, J.A. Robles-Linares, G. Garcia Luna, D. Axinte, et al., Machining of long ceramic fibre reinforced metal matrix composites – How could temperature influence the cutting mechanisms? International Journal of Machine Tools and Manufacture 185 (2023) 103994. https://doi.org/10.1016/j.ijmachtools.2023.103994.
M.D. Hayat, H. Singh, Z. He, P. Cao, Titanium metal matrix composites: an overview. Composites Part A: Applied Science and Manufacturing 121 (2019) 418–438. https://doi.org/10.1016/j.compositesa.2019.04.005.
P.J. Doorbar, S. Kyle-Henney, Development of continuously-reinforced metal matrix composites for aerospace applications. In: Comprehensive Composite Materials II, Elsevier (2018), pp. 439–463. https://doi.org/10.1016/B978-0-12-803581-8.09983-5.
Z. Liao, A. Abdelhafeez, H. Li, Y. Yang, O.G. Diaz, D. Axinte, State-of-the-art of surface integrity in machining of metal matrix composites. International Journal of Machine Tools and Manufacture 143 (2019) 63–91. https://doi.org/10.1016/j.ijmachtools.2019.05.006.
H.W. Meyer, D.S. Kleponis, Modeling the high strain rate behavior of titanium undergoing ballistic impact and penetration. International Journal of Impact Engineering 26 (2001) 509–521.
[6] D.R. Lesuer, Experimental Investigation of Material Models for Ti-6Al-4V and 2024-T3. FAA Report DOT/FAA/AR-00/25, 2000. The commonly used Lee–Lin and Lesuer parameter sets are also tabulated and compared in Rodríguez et al.
J.M. Rodríguez, S. Larsson, J.M. Carbonell, P. Jonsén, Dislocation density based flow stress model applied to the PFEM simulation of orthogonal cutting processes of Ti-6Al-4V. Materials 13(8) (2020) 1979. https://doi.org/10.3390/ma13081979. This article tabulates multiple published Johnson–Cook parameter sets, including the Li–He set used for comparison here.
National Institute of Standards and Technology (NIST), Cryogenic Materials Properties: Ti-6Al-4V, thermal conductivity and linear thermal expansion data/reference list. https://trc.nist.gov/cryogenics/materials/Ti6Al4V/Ti6Al4
Simulation of interface damage in metal matrix composites under off-axis loading using cohesive zone model. Computational Materials Science 108 (2015) 42–47. https://doi.org/10.1016/j.commatsci.2015.05.030.
G.R. Johnson, W.H. Cook, A constitutive model and data for metals subjected to large strains, high strain rates and high temperatures. Proceedings of the 7th International Symposium on Ballistics (1983) 541–547.
M. Sima, T. Özel, Modified material constitutive models for serrated chip formation simulations and experimental validation in machining of titanium alloy Ti-6Al-4V. International Journal of Machine Tools and Manufacture 50 (2010) 943–960. https://doi.org/10.1016/j.ijmachtools.2010.08.004.
T. Özel, T. Altan, Determination of workpiece flow stress and friction at the chip–tool contact for high-speed cutting. International Journal of Machine Tools and Manufacture 40 (2000) 133–152. https://doi.org/10.1016/S0890-6955(99)00051-6.
[14] M. Shet, X. Deng, Finite element analysis of the orthogonal metal cutting process. Journal of Materials Processing Technology 105 (2000) 95–109. https://doi.org/10.1016/S0924-0136(00)00578-6.
[15] M. Bäker, J. Rösler, C. Siemers, A finite element model of high speed metal cutting with adiabatic shearing. Computers & Structures 80 (2002) 495–513. https://doi.org/10.1016/S0045-7949(02)00023-8.
P.P. Camanho, C.G. Dávila, Mixed-mode decohesion finite elements for the simulation of delamination in composite materials. NASA/TM-2002-211737 (2002).
W.L. Oberkampf, C.J. Roy, Verification and Validation in Scientific Computing. Cambridge University Press (2010).
T. Belytschko, W.K. Liu, B. Moran, K. Elkhodary, Nonlinear Finite Elements for Continua and Structures, 2nd ed. Wiley (2014).
X. Han, D. Xu, D. Axinte, Z. Liao, H.N. Li, On understanding the specific cutting mechanisms governing the workpiece surface integrity in metal matrix composites machining. Journal of Materials Processing Technology 288 (2021) 116875. https://doi.org/10.1016/j.jmatprotec.2020.116875.
C.R. Dandekar, Y.C. Shin, Laser-assisted machining of a fiber reinforced metal matrix composite. Journal of Manufacturing Science and Engineering 132 (2010). https://doi.org/10.1115/1.4002548.
T. Özel, et al., Numerical Analysis of Serrated Chip Formation Mechanism with Johnson-Cook Parameters in Micro-Cutting of Ti6Al4V. Metals 11 (2021) 102. https://doi.org/10.3390/met11010102.










.png)




















